Home Power management DC/DC power modules Power modules (integrated inductor)
Home
Power management
DC/DC power modules
Power modules (integrated inductor)
NEW

TPSM828302

ACTIVE

2.25-V to 5.5-V, 2-A high-efficiency step-down power module with integrated inductor

Order now
Data sheet

TPSM828302

ACTIVE
Data sheet Order now

Product details

Iout (max) (A) 2 Vin (max) (V) 5.5 Vin (min) (V) 2.25 Vout (max) (V) 4.5 Vout (min) (V) 0.5 Rating Catalog Operating temperature range (°C) -40 to 125 Topology Synchronous Buck Features 1.2-V compatible control inputs, EMI Tested, Enable, Light Load Efficiency, Output discharge, Overcurrent protection, Power good Control mode DCS-Control Switching frequency (max) (Hz) 4000 Switching frequency (min) (Hz) 4000
Iout (max) (A) 2 Vin (max) (V) 5.5 Vin (min) (V) 2.25 Vout (max) (V) 4.5 Vout (min) (V) 0.5 Rating Catalog Operating temperature range (°C) -40 to 125 Topology Synchronous Buck Features 1.2-V compatible control inputs, EMI Tested, Enable, Light Load Efficiency, Output discharge, Overcurrent protection, Power good Control mode DCS-Control Switching frequency (max) (Hz) 4000 Switching frequency (min) (Hz) 4000
QFN-FCMOD (RDS) 9 9 mm² 3 x 3
  • 2.25-V to 5.5-V input voltage range
  • 0.5-V to 4.5-V adjustable output voltage
  • 1% FB voltage accuracy (–40°C to 125°C T J)
  • Optimized EMI performance
  • Facilitates CISPR 11/32 compliance
    • Integrated on-chip noise-filtering capacitors
    • Measurements according to CISPR available
  • Excellent transient response
  • 7-µA operating quiescent current
  • 2.0-MHz switching frequency
  • 35-mΩ and 18-mΩ internal power MOSFETs
  • DCS-Control topology
  • MODE pin for conduction mode selection
  • Supports 1.2-V GPIO
  • 100% duty cycle for lowest dropout
  • Active output discharge
  • Power-good output
  • Thermal shutdown protection
  • Hiccup or latch-off OCP/OVP
  • SIMPLIS model available
  • 2.25-V to 5.5-V input voltage range
  • 0.5-V to 4.5-V adjustable output voltage
  • 1% FB voltage accuracy (–40°C to 125°C T J)
  • Optimized EMI performance
  • Facilitates CISPR 11/32 compliance
    • Integrated on-chip noise-filtering capacitors
    • Measurements according to CISPR available
  • Excellent transient response
  • 7-µA operating quiescent current
  • 2.0-MHz switching frequency
  • 35-mΩ and 18-mΩ internal power MOSFETs
  • DCS-Control topology
  • MODE pin for conduction mode selection
  • Supports 1.2-V GPIO
  • 100% duty cycle for lowest dropout
  • Active output discharge
  • Power-good output
  • Thermal shutdown protection
  • Hiccup or latch-off OCP/OVP
  • SIMPLIS model available

The TPSM82830x is an easy-to-use, synchronous, step-down, DC/DC module family with integrated inductor and integrated on-chip noise-filtering capacitors. Based on the DCS-Control topology, the devices provide a fast transient response with small output capacitance. The internal reference allows to regulate the output voltage down to 0.5 V with a high feedback voltage accuracy of 1% over the junction temperature range of –40°C to 125°C.

The TPSM82830x has a MODE pin to control the device mode of operation. Power save mode maintains high efficiency down to very light loads for extending the system battery run-time. Forced-PWM mode maintains a continuous conduction mode to make sure the least ripple in the output voltage and a quasi-fixed switching frequency. The devices feature a Power-Good signal and a well-controlled internal soft-start circuit. The devices are able to operate in 100% mode. For fault protection, the devices incorporate a HICCUP short-circuit protection as well as a thermal shutdown. The family is available in a 3.0-mm × 3.0-mm × 2.0-mm QFN package.

The TPSM82830x is an easy-to-use, synchronous, step-down, DC/DC module family with integrated inductor and integrated on-chip noise-filtering capacitors. Based on the DCS-Control topology, the devices provide a fast transient response with small output capacitance. The internal reference allows to regulate the output voltage down to 0.5 V with a high feedback voltage accuracy of 1% over the junction temperature range of –40°C to 125°C.

The TPSM82830x has a MODE pin to control the device mode of operation. Power save mode maintains high efficiency down to very light loads for extending the system battery run-time. Forced-PWM mode maintains a continuous conduction mode to make sure the least ripple in the output voltage and a quasi-fixed switching frequency. The devices feature a Power-Good signal and a well-controlled internal soft-start circuit. The devices are able to operate in 100% mode. For fault protection, the devices incorporate a HICCUP short-circuit protection as well as a thermal shutdown. The family is available in a 3.0-mm × 3.0-mm × 2.0-mm QFN package.
open-in-new Find other Power modules (integrated inductor)
Download View video with transcript Video

Similar products you might be interested in

open-in-new Compare alternates
Pin-for-pin with same functionality to the compared device
NEW TPSM828301 ACTIVE 2.25-V to 5.5-V, 1-A high-efficiency step-down power module with integrated inductor Lower output current module alternative.
NEW TPSM828303 ACTIVE 2.25-V to 5.5-V, 3-A, low-noise step-down module with integrated inductor in QFN package Higher output current module alternative.
Similar functionality to the compared device
TPSM82822 ACTIVE 5.5-V input, 2-A step-down module with integrated inductor in 2 x 2.5 x 1.1-mm μSIP package 2-A step-down module in a smaller 2 mm x 2.5 mm MicroSiP package

Technical documentation

star =Top documentation for this product selected by TI
No results found. Please clear your search and try again.
View all 2
Type Title Date
* Data sheet TPSM82830x, 2.25-V to 5.5-V input, 1-, 2-, 3-A Step-Down Power Module With Integrated Inductor datasheet (Rev. A) PDF | HTML 05 Dec 2023
Certificate TPSM828302AEVM-245 EU Declaration of Conformity (DoC) 26 Jul 2023

Design & development

For additional terms or required resources, click any title below to view the detail page where available.

Package Pins Download
QFN-FCMOD (RDS) 9 View options
TI's Standard Terms and Conditions for Evaluation Items apply.

Ordering & quality

Information included:
  • RoHS
  • REACH
  • Device marking
  • Lead finish/Ball material
  • MSL rating/Peak reflow
  • MTBF/FIT estimates
  • Material content
  • Qualification summary
  • Ongoing reliability monitoring
Information included:
  • Fab location
  • Assembly location

Support & training

TI E2E™ forums with technical support from TI engineers

View all forum topics

Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.

If you have questions about quality, packaging or ordering TI products, see TI support. ​​​​​​​​​​​​​​

Videos